source: svn/trunk/newcon3bcm2_21bu/toolchain/mips-linux-uclibc/include/linux/serial.h

/*
 * include/linux/serial.h
 *
 * Copyright (C) 1992 by Theodore Ts'o.
 * 
 * Redistribution of this file is permitted under the terms of the GNU 
 * Public License (GPL)
 */

#ifndef _LINUX_SERIAL_H
#define _LINUX_SERIAL_H

struct serial_struct {
        int     type;
        int     line;
        unsigned int    port;
        int     irq;
        int     flags;
        int     xmit_fifo_size;
        int     custom_divisor;
        int     baud_base;
        unsigned short  close_delay;
        char    io_type;
        char    reserved_char[1];
        int     hub6;
        unsigned short  closing_wait; /* time to wait before closing */
        unsigned short  closing_wait2; /* no longer used... */
        unsigned char   *iomem_base;
        unsigned short  iomem_reg_shift;
        unsigned int    port_high;
        unsigned long   iomap_base;     /* cookie passed into ioremap */
};

/*
 * For the close wait times, 0 means wait forever for serial port to
 * flush its output.  65535 means don't wait at all.
 */
#define ASYNC_CLOSING_WAIT_INF  0
#define ASYNC_CLOSING_WAIT_NONE 65535

/*
 * These are the supported serial types.
 */
#define PORT_UNKNOWN    0
#define PORT_8250       1
#define PORT_16450      2
#define PORT_16550      3
#define PORT_16550A     4
#define PORT_CIRRUS     5       /* usurped by cyclades.c */
#define PORT_16650      6
#define PORT_16650V2    7
#define PORT_16750      8
#define PORT_STARTECH   9       /* usurped by cyclades.c */
#define PORT_16C950     10      /* Oxford Semiconductor */
#define PORT_16654      11
#define PORT_16850      12
#define PORT_RSA        13      /* RSA-DV II/S card */
#define PORT_MAX        13

#define SERIAL_IO_PORT  0
#define SERIAL_IO_HUB6  1
#define SERIAL_IO_MEM   2

struct serial_uart_config {
        char    *name;
        int     dfl_xmit_fifo_size;
        int     flags;
};

#define UART_CLEAR_FIFO         0x01
#define UART_USE_FIFO           0x02
#define UART_STARTECH           0x04
#define UART_NATSEMI            0x08

/*
 * Definitions for async_struct (and serial_struct) flags field
 */
#define ASYNC_HUP_NOTIFY 0x0001 /* Notify getty on hangups and closes 
                                   on the callout port */
#define ASYNC_FOURPORT  0x0002  /* Set OU1, OUT2 per AST Fourport settings */
#define ASYNC_SAK       0x0004  /* Secure Attention Key (Orange book) */
#define ASYNC_SPLIT_TERMIOS 0x0008 /* Separate termios for dialin/callout */

#define ASYNC_SPD_MASK  0x1030
#define ASYNC_SPD_HI    0x0010  /* Use 56000 instead of 38400 bps */

#define ASYNC_SPD_VHI   0x0020  /* Use 115200 instead of 38400 bps */
#define ASYNC_SPD_CUST  0x0030  /* Use user-specified divisor */

#define ASYNC_SKIP_TEST 0x0040 /* Skip UART test during autoconfiguration */
#define ASYNC_AUTO_IRQ  0x0080 /* Do automatic IRQ during autoconfiguration */
#define ASYNC_SESSION_LOCKOUT 0x0100 /* Lock out cua opens based on session */
#define ASYNC_PGRP_LOCKOUT    0x0200 /* Lock out cua opens based on pgrp */
#define ASYNC_CALLOUT_NOHUP   0x0400 /* Don't do hangups for cua device */

#define ASYNC_HARDPPS_CD        0x0800  /* Call hardpps when CD goes high  */

#define ASYNC_SPD_SHI   0x1000  /* Use 230400 instead of 38400 bps */
#define ASYNC_SPD_WARP  0x1010  /* Use 460800 instead of 38400 bps */

#define ASYNC_LOW_LATENCY 0x2000 /* Request low latency behaviour */

#define ASYNC_BUGGY_UART  0x4000 /* This is a buggy UART, skip some safety
                                  * checks.  Note: can be dangerous! */

#define ASYNC_AUTOPROBE  0x8000 /* Port was autoprobed by PCI or PNP code */

#define ASYNC_FLAGS     0x7FFF  /* Possible legal async flags */
#define ASYNC_USR_MASK  0x3430  /* Legal flags that non-privileged
                                 * users can set or reset */

/* Internal flags used only by kernel/chr_drv/serial.c */
#define ASYNC_INITIALIZED       0x80000000 /* Serial port was initialized */
#define ASYNC_NORMAL_ACTIVE     0x20000000 /* Normal device is active */
#define ASYNC_BOOT_AUTOCONF     0x10000000 /* Autoconfigure port on bootup */
#define ASYNC_CLOSING           0x08000000 /* Serial port is closing */
#define ASYNC_CTS_FLOW          0x04000000 /* Do CTS flow control */
#define ASYNC_CHECK_CD          0x02000000 /* i.e., CLOCAL */
#define ASYNC_SHARE_IRQ         0x01000000 /* for multifunction cards
                                             --- no longer used */
#define ASYNC_CONS_FLOW         0x00800000 /* flow control for console  */

#define ASYNC_BOOT_ONLYMCA      0x00400000 /* Probe only if MCA bus */
#define ASYNC_INTERNAL_FLAGS    0xFFC00000 /* Internal flags */

/*
 * Multiport serial configuration structure --- external structure
 */
struct serial_multiport_struct {
        int             irq;
        int             port1;
        unsigned char   mask1, match1;
        int             port2;
        unsigned char   mask2, match2;
        int             port3;
        unsigned char   mask3, match3;
        int             port4;
        unsigned char   mask4, match4;
        int             port_monitor;
        int     reserved[32];
};

/*
 * Serial input interrupt line counters -- external structure
 * Four lines can interrupt: CTS, DSR, RI, DCD
 */
struct serial_icounter_struct {
        int cts, dsr, rng, dcd;
        int rx, tx;
        int frame, overrun, parity, brk;
        int buf_overrun;
        int reserved[9];
};

#endif /* _LINUX_SERIAL_H */